超声波清洗机安全操作规程_洁升超声波清洗机
1 cleaning scale
1.1 This machine is a special person specializing in equipment, others may not operate without authorization.
1 清洗规模
1.2Ultrasonic cleaning machine is used for secondary cleaning of parts. Uncleaned parts must not be put into the machine for cleaning. 1.3 The scale of cleaning of the machine: engine parts such as engine block, cylinder head, crankshaft, camshaft, connecting rod piston, air compressor, bearings, steering gear, transmission shaft and gear, reducer gear, etc. 2 Operation method
1.1本机为专人专管设备，其他人不得擅自操作。
2.1 The appropriate clean water is taken in the cleaning tank, and the liquid level is determined by the immersed side vibrating box.
1.2超声波清洗机用于零部件的二次清洗，未经清洗过的零部件不得放入本机清洗。 1.3本机清洗规模：发动机缸体、缸盖、曲轴、凸轮轴、连杆活塞、空压机等发动机零部件，轴承、方向机、变速器的轴及齿轮、减速器齿轮等。 2 操作方法
2.2 Close the power switch on the rear panel of the control cabinet, start the electronically controlled heating switch, and point the white scale line on the water temperature adjustment knob to the appropriate temperature, usually 50 ° C \u0026 mdash ^ fen ^ 55 ° C in winter and 60 ° C - 65 ° C in winter. . The maximum temperature of the cleaning solution must not exceed 70 °C during use.
2.1清洗池内参加恰当清水，液面高度以浸没侧振盒为准。
2.3 First wash the cleaning agent with warm water in a water bucket and mix well to dissolve it. When the water temperature in the cleaning tank rises to 40 °C, it will participate in the water tank. The cleaning agent is diluted with 1-2% water (about 5 to 9 kg of cleaning agent).
2.2合上控制柜后面板上的电源开关，发动电控加热开关，将水温调节旋钮上的白色刻度线指向恰当的温度，通常夏天为50℃—55℃冬天为60℃－65℃。在使用过程中，清洗液最高温度不得超过70℃。
2.4 Place the parts in the net basket and put them into the cleaning tank quietly. The cleaning parts should be turned on more than 60% of the cleaning tank to prevent whistling and damage the power supply.
2.3先用水桶将清洗剂用温水冲开搅匀，使其充沛溶解，待清洗槽水温升至40℃摆布时参加水槽中。清洗剂按1～2%兑水稀释（清洗剂约5～9公斤）。
2.5 After the water temperature reaches the reserved value, start cleaning, turn the ultrasonic bottom and side power knob clockwise to the maximum, press the ultrasonic start button, and the cleaning starts. To stop cleaning, press the ultrasonic abort button directly.
2.4将零部件置于网筐中悄悄放入清洗池内，散布均匀。清洗零件应达清洗槽内60％以上再开机，防止啸叫，损坏电源。
2.6 punctual cleaning: first set the cleaning time, set the punctual switch to the open position, then turn the two power knobs clockwise to the maximum, press the ultrasonic start button to start cleaning, after the punctual time, the ultrasonic power supply will be actively closed.
2.5水温到达预订值后开机清洗，将超声波底部与侧部功率旋钮顺时针旋至最大，按下超声波发动按钮，清洗开始。若要中止清洗，直接按超声波中止按钮。
2.7 After cleaning, the ultrasonic power supply should be enclosed, and then the cleaned parts should be taken out, and the residual cleaning liquid in each channel should be completely blown out with compressed air, and the appearance should be dried.
2.6守时清洗：先设定清洗时刻，将守时开关置开位，再顺时针将两功率旋钮旋至最大，按下超声波发动按钮清洗开始，到达守时时刻后，超声波电源将主动封闭。
2.8 If there is too much oil on the surface of the cleaning tank, it should be turned off by overflowing the equipment to prevent secondary pollution of the workpiece being cleaned. 3 Notes
2.7清洗结束后要封闭超声波电源，再取出清洗好的零部件，用压缩空气将各孔道中的残留清洗液完全吹尽，并将外表吹干。
3.1 After placing the workpiece, the water level of the washing machine sink shall not be lower than the side vibration plate. Take care when handling the workpiece to prevent violent bumps.
2.8若清洗池液面上存有过多油污，应翻开溢流设备将其扫除，以防被清洗工件的二次污染。 3 注意事项
3.2 The following conditions shall not be used to open the ultrasonic power supply: when the new cleaning liquid is used, the horizontal level of the cleaning liquid is greatly shaken; when the cleaning material is taken in and taken out; during the cleaning operation, the cleaning tank is aborted and the cleaning tank transducer is no noise.
3.1放入工件后，清洗超声波清洗机价格机水槽的水位不得低于旁边面振板。放取工件时要轻拿轻放，防止剧烈磕碰。
3.3冬天槽体内液体不能结冰，使用前先加热再发动超声波（25℃以上为佳）。
3.2以下情况不得敞开超声波电源：新参加清洗液，清洗液水平面有较大动摇时；参加和取出清洗物时；清洗作业中，俄然中止，清洗槽换能器无噪音时。
3.4不得将沸水直接参加清洗槽内，应常常定时整理清洗槽底部内的污泥，以防底部换能器过热而掉落损坏。
3.3冬天槽体内液体不能结冰，使用前先加热再发动超声波（25℃以上为佳）。
3.5接连作业时，如过热，机器将主动中止，冷却系统照旧作业，待降止适宜温度时，机器降主动敞开超声波。
3.4不得将沸水直接参加清洗槽内，应常常定时整理清洗槽底部内的污泥，以防底部换能器过热而掉落损坏。
3.6禁止从超声波控制柜进风口处溅入导电液体（如水）。 4 保护与养护
3.5接连作业时，如过热，机器将主动中止，冷却系统照旧作业，待降止适宜温度时，机器降主动敞开超声波。
4.1应常常查看控制柜与清洗槽的接地情况，必须接地杰出。
3.6禁止从超声波控制柜进风口处溅入导电液体（如水）。 4 保护与养护
4.2电源进线、控制柜与清洗槽之间连线插头应定时查看是不是连接可靠以及绝缘性与导电性。 4.3坚持机器内部各部件的清洗，不使用时封闭电源总开关。 4.4清洗液应及时沉积、过滤或替换，以保证清洗作用。 4.5防止对机器的磕碰或剧烈轰动。
